Overview
The SIPROTEC 7VU683 high speed busbar transfer (HBST) device is a compact multifunction unit which has been developed for very fast power supply transfer of busbar which is installed with big rotating loads.
For more detailed information on “SIPROTEC 7VU683” relays, refer to SIPROTEC 4 devices manuals.
To see other supported devices, click here.
HSBT General Settings
| Addr. | Parameter | C | Range | Default Setting | Note |
| Device Configuration | |||||
| 0103 | Setting group change option | Disable Enable |
Disable | ||
| 0158 | High speed busbar transfer | Disable Enable |
Enable | ||
| 0160 | Protection functions | Disable Enable |
Enable | Sectionalized single busbar w. 3-CB | |
| Power System Data 1-> Power System | |||||
| 0211 | Rated frequency | 50 Hz 60 Hz |
50 Hz | ||
| 0213 | VT connection of Line1 | Ua Ub Uc Uab Ubc Uca |
Uab | ||
| 0214 | VT connection of Line2 | Ua Ub Uc Uab Ubc Uca |
Uab | ||
| 0218 | VT connection of Line3 | Ua Ub Uc Uab Ubc Uca |
Uab | Single busbar with 3-CB | |
| 0280 | CT connection of Line1 | IA IB IC not connected |
IB | ||
| 0281 | CT connection of Line2 | IA IB IC not connected |
IB | ||
| 0282 | CT connection of Line3 | IA IB IC not connected |
IB | Single busbar with 3-CB | |
| 0283 | Voltage balancing factor of Line1 | 0.500<= … <=2.000 | 1.000 | ||
| 0284 | Voltage angle adjustment of Line1 | 0.0<= … <=359.9 | 0.0° | ||
| 0285 | Voltage balancing factor of Line2 | 0.500<= … <=2.000 | 1.000 | ||
| 0286 | Voltage angle adjustment of Line2 | 0.0<= … <=359.9 | 0.0° | ||
| 0287 | Voltage balancing factor of Line3 | 0.500<= … <=2.000 | 1.000 | Single busbar with 3-CB | |
| 0288 | Voltage angle adjustment of Line3 | 0.0<= … <=359.9 | 0.0° | Single busbar with 3-CB | |
| 8900 | Busbar live voltage threshold | 0.550<= … <=0.900 | 0.700 U/Un | ||
| 8901 | Busbar dead voltage threshold | 0.100<= … <=0.450 | 0.300 U/Un | ||
| 8902 | Line live voltage threshold | 0.550<= … <=0.900 | 0.700 U/Un | ||
| 8903 | Line dead voltage threshold | 0.100<= … <=0.450 | 0.300 U/Un | ||
| 8904 | Line dead current threshold | 0.05<= … <=0.50 | 0.10 I/In | ||
| Power System Data 1-> Function | |||||
| 0221 | High speed busbar transfer | ON OFF |
ON | ||
| 0226 | Protection functions | ON OFF |
ON | Sectionalized single busbar | |
| Power System Data 1-> VT’s | |||||
| 0231 | VT rated primary voltage Line1 | 0.15<= … <=1200.0 | 6.3 KV | ||
| 0232 | VT rated secondary voltage Line1 | 80<= … <=125 | 100 V | ||
| 0233 | VT rated primary voltage Line2 | 0.15<= … <=1200.0 | 6.3 KV | ||
| 0234 | VT rated secondary voltage Line2 | 80<= … <=125 | 100 V | ||
| 0241 | VT rated primary voltage Line3 | 0.15<= … <=1200.0 | 6.3 KV | Single busbar with 3-CB | |
| 0242 | VT rated secondary voltage Line3 | 80<= … <=125 | 100 V | Single busbar with 3-CB | |
| 0235 | VT rated primary voltage Busbar | 0.15<= … <=1200.0 | 6.3 KV | ||
| 0236 | VT rated secondary voltage Busbar | 80<= … <=125 | 100 V | ||
| Power System Data 1->CT’s | |||||
| 0251 | CT rated primary current Line1 | 100<=…<=20000 | 3000 A | ||
| 0252 | CT rated secondary current Line1 | 1 A 5 A |
1 A | ||
| 0253 | CT rated primary current Line2 | 100<=…<=20000 | 3000 A | ||
| 0254 | CT rated secondary current Line2 | 1 A 5 A |
1 A | ||
| 0259 | CT rated primary current Line3 | 100<=…<=20000 | 3000A | Single busbar with 3-CB | |
| 0260 | CT rated secondary current Line3 | 1 A 5 A |
1 A | Single busbar with 3-CB | |
| 0255 | CT rated primary current Busbar | 100<=…<=20000 | 3000 A | Sectionalized single busbar | |
| 0256 | CT rated secondary current Busbar | 1 A 5 A |
1 A | Sectionalized single busbar | |
| 0257A | Earth CT rated primary current Busbar | 100<=…<=20000 | 3000 A | Sectionalized single busbar | |
| 0258A | Earth CT rated secondary current Busbar | 1 A 5 A |
1 A | Sectionalized single busbar | |
| Power System Data 1->CB | |||||
| 0261 | Minimum TRIP command dura- tion | 0.01<=…<=10.00 | 0.20 sec | ||
| 0262 | Minimum CLOSE command duration | 0.01<=…<=10.00 | 0.20 sec | ||
Single Busbar with 2-CB
| Addr. | Parameter | C | Range | Default Setting | Note |
| HSBT->General | |||||
| 8801 | CB1 closing time | 20<=…<=150 | 70 ms | ||
| 8802 | CB2 closing time | 20<=…<=150 | 70 ms | ||
| 8804 | Maximum permitted HSBT operating Time | 10<=…<=60 | 20 sec | ||
| 8805 | Switching direction Line1->Line2 | ON OFF |
OFF | ||
| 8806 | Switching direction Line2->Line1 | ON OFF |
OFF | ||
| 8811 | Line1->Line2 LVLSH permitted | YES NO |
NO | ||
| 8812 | Line2->Line1 LVLSH permitted | YES NO |
NO | ||
| 8817 | Manually reset | YES NO |
NO | ||
| 8818 | Time delay to readiness | 5<=…<=60 | 10 sec | ||
| 8819 | Time delay to un-readiness | 10<=…<=60 | 10 sec | ||
| 8820 | HSBT test mode | ON OFF |
OFF | ||
| 8837 | Fault Detection Ubus | ON OFF |
ON | ||
| 8838 | Motor Start Detection Ubus | ON OFF |
ON | ||
| HSBT->Start Condition | |||||
| 8821 | NORMAL | OFF PARALLEL Auto PARAL. Half-Auto SIMULTANEOUS SEQUENTIAL |
PARALLEL Auto | ||
| 8822 | FAULT start type A | OFF SIMULTANEOUS SEQUENTIAL |
SEQUENTIAL | ||
| 8898 | FAULT start type B | OFF SIMULTANEOUS SEQUENTIAL |
SIMULTANEOUS | ||
| 8823 | Under-voltage | OFF SIMULTANEOUS SEQUENTIAL |
SIMULTANEOUS | ||
| 8826 | Under-voltage threshold | 0.200<=…<=0.950 | 0.880 U/Un | ||
| 8827 | Under-voltage time Delay | 0<= …<=5000 | 10 ms | ||
| 8824 | Under-frequency | OFF SIMULTANEOUS SEQUENTIAL |
SIMULTANEOUS | ||
| 8829 | Under-frequency threshold | 45.00<=…<=49.50 | 47.50 Hz | fn = 50 Hz | |
| 8829 | Under-frequency threshold | 55.00<=…<=59.50 | 57.00 Hz | fn = 60 Hz | |
| 8830 | Under-frequency time Delay | 0<=…<=1000 | 10 ms | ||
| 8832 | Reverse power | OFF SIMULTANEOUS SEQUENTIAL |
OFF | ||
| 8833 | Reverse power time delay | 0<=…<=1000 | 10 ms | ||
| 8834 | Change rate of frequency | OFF SIMULTANEOUS SEQUENTIAL |
OFF | ||
| 8835 | Change rate of frequency threshold | -10.0<=…<=-0.5 | -0.5 Hz/s | ||
| 8836 | Change rate of frequency time delay | 0<=…<=1000 | 10 ms | ||
| 8825 | Inadvertent CB Open | OFF ON |
ON | ||
| 8831 | Mono-direction against NORMAL | YES NO |
NO | ||
| HSBT->Transfer Mode | |||||
| 8841 | FAST | OFF ON |
ON | ||
| 8842 | REAL-TIME FAST | OFF ON |
ON | ||
| 8843. | IN-PHASE | OFF ON |
ON | ||
| 8844 | RES-VOLT | OFF ON |
ON | ||
| 8845 | LONG-TIME | OFF ON |
ON | ||
| HSBT-->Transfer Set | |||||
| 8851 | PARALLEL sequence: delta frequency | 0.02<=…<=2.00 | 0.10 Hz | ||
| 8852 | PARALLEL sequence: delta U | 1.0<=…<=40.0 | 2.0 V | ||
| 8853 | PARALLEL sequence: delta phase angle | 2.0<=…<=80.0 | 10.0 ° | ||
| 8854 | PARALLEL Auto: CB open time delay | 0.00<=…<=2.00 | 0.10 sec | ||
| 8857 | SIMULTANEOUS sequence: CB close time delay | 0<=…<=40 | 0 ms | ||
| 8873 | SIMULTANEOUS sequence: CB open time delay | 0<=…<=40 | 0 ms | ||
| 8858 | FAST mode: delta frequency | 0.50<=…<=5.00 | 3.00 Hz | ||
| 8859 | FAST mode: delta phase angle | 10.0<=…<=50.0 | 20.0 ° | ||
| 8860 | FAST mode: under-voltage block | 0.500<=…<=0.900 | 0.700 U/Un | ||
| 8861 | REAL-TIME FAST mode: delta frequency | 1.00<=…<=15.00 | 3.00 Hz | ||
| 8862 | REAL-TIME FAST mode: Udiff/f | 1.00<=…<=1.33 | 1.33 p.u. | ||
| 8863 | REAL-TIME FAST mode: delta phase angle | 70.0<=…<=90.0 | 90.0 ° | ||
| 8864 | REAL-TIME FAST mode: under-voltage block | 0.500<=…<=0.900 | 0.700 U/Un | ||
| 8868 | IN-PHASE mode: delta frequency | 1.00<=…<=15.00 | 5.00 Hz | ||
| 8869 | IN-PHASE mode: delta phase angle | 0.5<=…<=20.0 | 5.0 ° | ||
| 8870 | IN-PHASE mode: under-voltage block | 0.200<=…<=0.800 | 0.400 U/Un | ||
| 8871 | RES-VOLT mode: threshold | 0.200<=…<=0.600 | 0.300 U/Un | ||
| 8872 | LONG-TIME mode: threshold | 0.50<=…<=10.00 | 3.00 sec | ||
Sectionalized Single Busbar with 3-CB
| Addr. | Parameter | C | Range | Default Setting | Note |
| HSBT->General | |||||
| 8801 | CB1 Closing Time | 20<=…<=150 | 70 ms | ||
| 8802 | CB2 Closing Time | 20<=…<=150 | 70 ms | ||
| 8803 | CB3 Closing Time | 20<=…<=150 | 70 ms | ||
| 8804 | Maximum permitted HSBT operating time | 10<=…<=60 | 20 sec | ||
| 8805 | Switching direction Line1->Line2 | ON OFF |
OFF | ||
| 8806 | Switching direction Line2->Line1 | ON OFF |
OFF | ||
| 8807 | Switching direction Busbar1->Busbar2 | ON OFF |
OFF | ||
| 8808 | Switching direction Busbar1->Line1 | ON OFF |
OFF | ||
| 8809 | Switching direction Busbar2->Busbar1 | ON OFF |
OFF | ||
| 8810 | Switching direction Busbar2->Line2 | ON OFF |
OFF | ||
| 8811 | Line1->Line2 LVLSH permitted | YES NO |
NO | ||
| 8812 | Line2->Line1 LVLSH permitted | YES NO |
NO | ||
| 8813 | Busbar1->Busbar2 LVLSH permitted | YES NO |
NO | ||
| 8814 | Busbar2->Busbar1 LVLSH permitted | YES NO |
NO | ||
| 8815 | Busbar1->Line1 LVLSH permitted | YES NO |
NO | ||
| 8816 | Busbar2->Line2 LVLSH permitted | YES NO |
NO | ||
| 8817 | Manually reset | YES NO |
NO | ||
| 8818 | Time delay to readiness | 5<=…<=60 | 10 sec | ||
| 8819 | Time delay to un-readiness | 10<=…<=60 | 10 sec | ||
| 8820 | HSBT test mode | ON OFF |
OFF | ||
| 8837 | Fault Detection Ubus | ON OFF |
ON | ||
| 8838 | Motor Start Detection Ubus | ON OFF |
ON | ||
| HSBT->Start Condition | |||||
| 8821 | NORMAL | OFF PARALLEL Auto PARAL. Half-Auto SIMULTANEOUS SEQUENTIAL |
PARALLEL Auto | ||
| 8822 | FAULT start type A | OFF SIMULTANEOUS SEQUENTIAL |
SEQUENTIAL | ||
| 8898 | FAULT start type B | OFF SIMULTANEOUS SEQUENTIAL |
SIMULTANEOUS | ||
| 8823 | Under-voltage | OFF SIMULTANEOUS SEQUENTIAL |
SIMULTANEOUS | ||
| 8826 | Under-voltage threshold | 0.200<=…<=0.950 | 0.880 U/Un | ||
| 8827 | Under-voltage time delay | 0<= …<=5000 | 10 ms | ||
| 8824 | Under-frequency | OFF SIMULTANEOUS SEQUENTIAL |
SIMULTANEOUS | ||
| 8829 | Under-frequency threshold | 45.00<=…<=49.50 | 47.50 Hz | fn = 50 Hz | |
| 8829 | Under-frequency threshold | 55.00<=…<=59.50 | 57.00 Hz | fn = 60 Hz | |
| 8830 | Under-frequency time delay | 0<= …<=1000 | 10 ms | ||
| 8832 | Reverse power | OFF SIMULTANEOUS SEQUENTIAL |
OFF | ||
| 8833 | Reverse power time delay | 0<=…<=1000 | 10 ms | ||
| 8834 | Change rate of frequency | OFF SIMULTANEOUS SEQUENTIAL |
OFF | ||
| 8835 | Change rate of frequency threshold | -10.0<=…<=-0.5 | -0.5 Hz/s | ||
| 8836 | Change rate of frequency time delay | 0<= …<=1000 | 10 ms | ||
| 8825 | Inadvertent CB open | OFF ON |
ON | ||
| 8831 | Mono-direction against NORMAL | YES NO |
NO | ||
| HSBT->Transfer Mode | |||||
| 8841 | FAST | OFF ON |
ON | ||
| 8842 | REAL-TIME FAST | OFF ON |
ON | ||
| 8843 | IN-PHASE | OFF ON |
ON | ||
| 8844 | RES-VOLT | OFF ON |
ON | ||
| 8845 | LONG-TIME | OFF ON |
ON | ||
| HSBT-->Transfer Set | |||||
| 8851 | PARALLEL sequence: delta frequency | 0.02<=…<=2.00 | 0.10 Hz | ||
| 8852 | PARALLEL sequence: delta U | 1.0<=…<=40.0 | 2.0 V | ||
| 8853 | PARALLEL sequence: delta phase angle | 2.0<=…<=80.0 | 10.0 ° | ||
| 8854 | PARALLEL Auto: CB open time delay | 0.00<=…<=2.00 | 0.10 sec | ||
| 8857 | SIMULTANEOUS sequence: CB close time delay | 0<=…<=40 | 0 ms | ||
| 8873 | SIMULTANEOUS sequence: CB open time delay | 0<=…<=40 | 0 ms | ||
| 8858 | FAST mode: delta frequency | 0.50<=…<=5.00 | 3.00 Hz | ||
| 8859 | FAST mode: delta phase angle | 10.0<=…<=50.0 | 20.0 ° | ||
| 8860 | FAST mode: under-voltage block | 0.500<=…<=0.900 | 0.700 U/Un | ||
| 8861 | REAL-TIME FAST mode: delta frequency | 1.00<=…<=15.00 | 3.00 Hz | ||
| 8862 | REAL-TIME FAST mode: Udiff/f | 1.00<=…<=1.33 | 1.33 p.u. | ||
| 8863 | REAL-TIME FAST mode: delta phase angle | 70.0<=…<=90.0 | 90.0 ° | ||
| 8864 | REAL-TIME FAST mode: under-voltage block | 0.500<=…<=0.900 | 0.700 U/Un | ||
| 8868 | IN-PHASE mode: delta frequency | 1.00<=…<=15.00 | 5.00 Hz | ||
| 8869 | IN-PHASE mode: delta phase angle | 0.5<=…<=20.0 | 5.0 ° | ||
| 8870 | IN-PHASE mode: under-voltage block | 0.200<=…<=0.800 | 0.400 U/Un | ||
| 8871 | RES-VOLT mode: threshold | 0.200<=…<=0.600 | 0.300 U/Un | ||
| 8872 | LONG-TIME mode: threshold | 0.50<=…<=10.00 | 3.00 sec | ||
Single Busbar with 3-CB
| Addr. | Parameter | C | Range | Default Setting | Note |
| HSBT->General | |||||
| 8801 | CB1 closing time | 20<=…<=150 | 70 ms | ||
| 8802 | CB2 closing time | 20<=…<=150 | 70 ms | ||
| 8803 | CB3 closing time | 20<=…<=150 | 70 ms | ||
| 8804 | Maximum permitted HSBT operating Time | 10<=…<=60 | 20 sec | ||
| 8805 | Switching direction Line1->Line2 | ON OFF | OFF | ||
| 8806 | Switching direction Line2->Line1 | ON OFF | OFF | ||
| 8890 | Switching direction Line1->Line3 | ON OFF | OFF | ||
| 8891 | Switching direction Line3->Line1 | ON OFF | OFF | ||
| 8892 | Switching direction Line2->Line3 | ON OFF | OFF | ||
| 8893 | Switching direction Line3 ->Line2 | ON OFF | OFF | ||
| 8811 | Line1->Line2 LVLSH permitted | YES NO | NO | ||
| 8812 | Line2->Line1 LVLSH permitted | YES NO | NO | ||
| 8894 | Line1->Line3 LVLSH permitted | YES NO | NO | ||
| 8895 | Line3->Line1 LVLSH permitted | YES NO | NO | ||
| 8896 | Line2->Line3 LVLSH permitted | YES NO | NO | ||
| 8897 | Line3 ->Line2 LVLSH permitted | YES NO | NO | ||
| 8817 | Manually reset | YES NO | NO | ||
| 8818 | Time delay to readiness | 5<=…<=60 | 10 sec | ||
| 8819 | Time delay to un-readiness | 10<=…<=60 | 10 sec | ||
| 8820 | HSBT test mode | ON OFF | OFF | ||
| 8837 | Fault Detection Ubus | ON OFF | ON | ||
| 8838 | Motor Start Detection Ubus | ON OFF | ON | ||
| HSBT->Start Condition | |||||
| 8821 | NORMAL | OFF PARALLEL Auto PARAL. Half-Auto SIMULTANEOUS SEQUENTIAL |
PARALLEL Auto | ||
| 8822 | FAULT start type A | OFF SIMULTANEOUS SEQUENTIAL | SEQUENTIAL | ||
| 8898 | FAULT start type B | OFF SIMULTANEOUS SEQUENTIAL | SIMULTANEOUS | ||
| 8823 | Under-voltage | OFF SIMULTANEOUS SEQUENTIAL | SIMULTANEOUS | ||
| 8826 | Under-voltage threshold | 0.200<=…<=0.950 | 0.880 U/Un | ||
| 8827 | Under-voltage time delay | 0<= …<=5000 | 10 ms | ||
| 8824 | Under-frequency | OFF SIMULTANEOUS SEQUENTIAL | SIMULTANEOUS | ||
| 8829 | Under-frequency threshold | 45.00<=…<=49.50 | 47.50 Hz | fn = 50 Hz | |
| 8829 | Under-frequency threshold | 55.00<=…<=59.50 | 57.00 Hz | fn = 60 Hz | |
| 8830 | Under-frequency time delay | 0<= …<=1000 | 10 ms | ||
| 8832 | Reverse power | OFF SIMULTANEOUS SEQUENTIAL | OFF | ||
| 8833 | Reverse power time delay | 0<= …<=1000 | 10 ms | ||
| 8834 | Change rate of frequency | OFF SIMULTANEOUS SEQUENTIAL | OFF | ||
| 8835 | Change rate of frequency threshold | -10.0<=…<=-0.5 | -0.5 Hz/s | ||
| 8836 | Change rate of frequency time delay | 0<= …<=1000 | 10 ms | ||
| 8825 | Inadvertent CB open | OFF ON | ON | ||
| 8831 | Mono-direction against NORMAL | YES NO | NO | ||
| HSBT->Transfer Mode | |||||
| 8841 | FAST | OFF ON | ON | ||
| 8842 | REAL-TIME FAST | OFF ON | ON | ||
| 8843 | IN-PHASE | OFF ON | ON | ||
| 8844 | RES-VOLT | OFF ON | ON | ||
| 8845 | LONG-TIME | OFF ON | ON | ||
| HSBT-->Transfer Set | |||||
| 8851 | PARALLEL sequence: delta frequency | 0.02<=…<=2.00 | 0.10 Hz | ||
| 8852 | PARALLEL sequence: delta U | 1.0<=…<=40.0 | 2.0 V | ||
| 8853 | PARALLEL sequence: delta phase angle | 2.0<=…<=80.0 | 10.0 ° | ||
| 8854 | PARALLEL Auto: CB open time delay | 0.00<=…<=2.00 | 0.10 sec | ||
| 8857 | SIMULTANEOUS sequence: CB close time delay | 0<=…<=40 | 0 ms | ||
| 8873 | SIMULTANEOUS sequence: CB open time delay | 0<=…<=40 | 0 ms | ||
| 8858 | FAST mode: delta frequency | 0.50<=…5.00 | 3.00 Hz | ||
| 8859 | FAST mode: delta phase angle | 10.0<=…<=50.0 | 20.0 ° | ||
| 8860 | FAST mode: under-voltage block | 0.500<=…<=0.900 | 0.700 U/Un | ||
| 8861 | REAL-TIME FAST mode: delta frequency | 1.00<=…<=15.00 | 3.00 Hz | ||
| 8862 | REAL-TIME FAST mode: Udiff/f | 1.00<=…<=1.33 | 1.33 p.u. | ||
| 8863 | REAL-TIME FAST mode: delta phase angle | 70.0<=…<=90.0 | 90.0 ° | ||
| 8864 | REAL-TIME FAST mode: under-voltage block | 0.500<=…<=0.900 | 0.700 U/Un | ||
| 8868 | IN-PHASE mode: delta frequency | 1.00<=…<=15.00 | 5.00 Hz | ||
| 8869 | IN-PHASE mode: phase angle | 0.5<=…<=20.0 | 5.0 ° | ||
| 8870 | IN-PHASE mode: under-voltage block | 0.200<=…<=0.800 | 0.400 U/Un | ||
| 8871 | RES-VOLT mode: threshold | 0.200<=…<=0.600 | 0.300 U/Un | ||
| 8872 | LONG-TIME mode: threshold | 0.50<=…<=10.00 | 3.00 sec | ||
Phase OverCurrent Protection
| Addr. | Parameter | C | Range | Default Setting | Note |
| Protection Functions->General | |||||
| 9000 | Phase over-current protection | ON OFF |
OFF | ||
| Protection Functions -> Voltage Control | |||||
| 9002 | Ph-ph under-voltage threshold | 1.0<=…<=125.0, 0 | 70.0 V | ||
| 9003 | U2 over-voltage threshold | 1.0<=…<=125.0, ∞ | 8.0 V | ||
| Protection Functions -> Phase O/C | |||||
| 9001 | Compound voltage control | YES NO |
YES | ||
| 9004 | Phase over-current I>threshold | 0.10<=…<=35.00 | 3.00 A | ||
| 9005 | Phase over-current I> time delay | 0.00<=…<=60.00, ∞ | 0.50 s | ||
| 9006 | Phase over-current I>>threshold | 0.10<=…<=35.00 | 5.00 A | ||
| 9007 | Phase over-current I>> time delay | 0.00<=…<=60.00, ∞ | 0.10 s | ||
Ground Overcurrent Protection
| Addr. | Parameter | C | Range | Default Setting | Note |
| Protection Functions-> General | |||||
| 9010 | Earth over-current protection | ON OFF |
OFF | ||
| 9018 | 3I0/IE assignment | IE 3I0 | 3I0 | ||
| Protection Functions -> Voltage Control | |||||
| 9012 | 3U0 over-voltage threshold | 1<=…<=200 | 30 V | ||
| Protection Functions -> Earth O/C | |||||
| 9011 | 3U0 Control | Yes No |
Yes | ||
| 9013 | Earth over-current le > threshold | 0.10<=…<=35.00 | 3.00 A | ||
| 9014 | Earth over-current le > time delay | 0.00<=…<=60.00, ∞ | 0.50 s | ||
| 9015 | Earth over-current le >> threshold | 0.10<=…<=35.00 | 5.00 A | ||
| 9016 | Earth over-current le >> time delay | 0.00<=…<=60.00, ∞ | 0.10 s | ||
Phase OverCurrent Protection against Switch-Onto-Fault
| Addr. | Parameter | C | Range | Default Setting | Note |
| Protection Functions -> General | |||||
| 9020 | Phase O/C switch-onto-fault protection | ON OFF |
OFF | ||
| 9019A | Active time for switch-onto-fault protection | 0.01<=…<=600.00 | 5.00 s | ||
| Protection Functions -> Voltage Control | |||||
| 9002 | Ph-ph under-voltage threshold | 1.0<=…<=125.0, 0 | 70.0 V | ||
| 9003 | U2 over-voltage threshold | 1.0<=…<=125.0,∞ | 8.0 V | ||
| Protection Functions -> Ph. O/C SOF | |||||
| 9021 | Compound voltage control | Yes No |
No | ||
| 9024 | Phase O/C I> switch-onto-fault threshold | 0.10<=…<=35.00 | 2.00 A | ||
| 9025 | Phase O/C I>switch-onto-fault time delay | 0.00<=…<=60.00, ∞ | 0.50 s | ||
| 9026 | Phase O/C I>>switch-onto-fault threshold | 0.10<=…<=35.00 | 4.00 A | ||
| 9027 | Phase O/C I>>switch-onto-fault time delay | 0.00<=…<=60.00, ∞ | 0.10 s | ||
Ground OverCurrent Protection against Switch-Onto-Fault
| Addr. | Parameter | C | Range | Default Setting | Note |
| Protection Functions -> General | |||||
| 9030 | Earth O/C switch-onto-fault protection | ON OFF |
OFF | ||
| 9018 | 3I0/IE assignment | IE 3I0 |
3I0 | ||
| 9019A | Active time for switch-onto-fault protection | 0.01<=…<=600.00 | 5.00 s | ||
| Protection Functions -> Voltage Control | |||||
| 9012 | 3U0 over-voltage threshold | 1<=…<=200 | 30 V | ||
| Protection Functions -> Earth O/C SOF | |||||
| 9031 | 3U0 Control | Yes No |
Yes | ||
| 9033 | Earth O/C le >switch-onto-fault threshold | 0.10<=…<=35.00 | 2.00 A | ||
| 9034 | Earth O/C le >switch-onto-fault time-delay | 0.00<=…<=60.00, ∞ | 0.50 s | ||
| 9035 | Earth O/C le >> switch-onto-fault threshold | 0.10<=…<=35.00 | 4.00 A | ||
| 9036 | Earth O/C le >>switch-onto-fault time-delay | 0.00<=…<=60.00, ∞ | 0.10 s | ||
VT Broken Wire Supervision
| Addr. | Parameter | C | Range | Default Setting | Note |
| Supervision | |||||
| 9101 | VT Broken Wire | ON OFF |
OFF | ||
Bus Voltage Sequence Supervision
| Addr. | Parameter | C | Range | Default Setting | Note |
| Supervision | |||||
| 9102 | Phase Sequence Busbar Voltage | ON OFF |
OFF | ||